Autore Topic: Drive 1581 E Floppy Drive 3,5"  (Letto 5929 volte)

Akeem

  • Neo-iscritto
  • *
  • Post: 11
  • Gioco Preferito: Ghostbusters
Drive 1581 E Floppy Drive 3,5"
« il: 25 Febbraio 2008, 04:22:23 »
 Ciao a tutti, sono riuscito a reperire un Drive 1581 Commodore 64, visto che il floppy drive ha un problema mi chiedevo se fosse possibile togliere l'unità 3,5 dal case del 1581 e inserircene uno PC 3,5 che vendono a pochi euro nei negozi d'informatica. E' uguale? Funge ugualmente?

mces

  • Utente
  • **
  • Post: 339
  • Gioco Preferito: fort apocalypse
Drive 1581 E Floppy Drive 3,5"
« Risposta #1 il: 25 Febbraio 2008, 13:00:01 »
 ASSOLUTAMENTE NO.
Innanzitutto il formato magnetico di formattazione è incompatibile, inoltre la periferica commodore è un SISTEMA a MICROPROCESSORE (6502) che colloquia via seriale con il C.64 e manovra la meccanica del drive.

Visto che il tutto è un sistema PROPRIETARIO non solo non è standard "PC" il formato magnetico del dischetto, ma è anche completamente diversa l'elettronica (intelligente sul drive del C.64) che governa la meccanica.

Se tu fossi esperto di elettronica & affini potresti studiare, nel caso fosse per te risolutivo, la possibilità di usare la SOLA meccanica di un vecchio drive per PC (inteso: telaio, motore rotazione, motore passo-passo delle testine, interruttori di fine corsa e presenza disco, testine magnetiche) o PARTE di essa per sostituire evantuali pezzi difettosi nel tuo vecchio drive.

Ciao!
Non esistono problemi, solo soluzioni.

Akeem

  • Neo-iscritto
  • *
  • Post: 11
  • Gioco Preferito: Ghostbusters
Drive 1581 E Floppy Drive 3,5"
« Risposta #2 il: 25 Febbraio 2008, 13:11:20 »
 Grazie per la risposta. E se ci inserissi un drive 3,5 amiga? Va bene oppure ha lo stesso problema che ha il drive per PC con il 1581?

Yurif999

  • Utente
  • **
  • Post: 86
    • http://www.facebook.com/juri.fossaroli
  • Gioco Preferito: Turrican
Drive 1581 E Floppy Drive 3,5"
« Risposta #3 il: 25 Febbraio 2008, 17:29:46 »
 tempo fa vendevano su ebay dei KIT 1581 dove ti vendevano la scocca, la mainboard del 1581 e basta. il floppy andava comprato a parte e andavano bene ALCUNI tipi di floppy x pc apportando una piccola modifica (per floppy intendo il lettore floppy completo) e se non ricordo male andavano BENISSIMO i lettori floppy amiga senza alcuna modifica.
comunque siccome la mia memoria e' un po.. "volatile" :P  ti suggerisco vivamente di fare alcune RICERCHE DETTAGLIATE su internet prima di provare a collegare qualsiasi lettore floppy.
ciao
JMP $EA31

vankue

  • Neo-iscritto
  • *
  • Post: 11
  • Gioco Preferito: ZAK MCKRAKEN AND THE ALIEN MINDBENDERS
Drive 1581 E Floppy Drive 3,5"
« Risposta #4 il: 25 Febbraio 2008, 21:23:32 »
 Il Chip Custom Amiga chiamato Paula, era anche in grado di leggere sia dischi da 3,5 pollici che dischi da 5,25 pollici (se veniva collegato un drive per floppy con formato adeguato), e di poter leggere e scrivere dischi in formato IBM PC, Atari TOS, Macintosh, Commodore 64, ed altri ancora.

zimox

  • Utente
  • **
  • Post: 171
  • Gioco Preferito: trolls & tribulations
Drive 1581 E Floppy Drive 3,5"
« Risposta #5 il: 27 Febbraio 2008, 22:14:59 »
 pubblico volentieri un progettino che ho fatto un po' di tempo fa
la memoria e' molto labile...mah!...buff....   lo portero' a vicenza.
so solo che ho preso un drive che avevo in casa controllando se era del tipo giusto, modificato il cavo flat, preso un alimentatore di un olivetti prodest
, un case 1541 che mi avanzava e ho messo tutto all 'interno con switch per jiffy e device

non sono sicuro ma pare che anche un drive da pc possa andare bene (il controller wdc lo permette)  l' importante e' che abbia il selettore per il D0/D1.
quelli dei pc sono tutti D1 ma dovrebbero avere almeno la pizzola da dissaldare per trasformarli in D0



back
http://i26.tinypic.com/2n89bnd.jpg
inside
http://i32.tinypic.com/1eaqmf.jpg
front
http://i27.tinypic.com/107nuwp.jpg
No c64?, no party!

vankue

  • Neo-iscritto
  • *
  • Post: 11
  • Gioco Preferito: ZAK MCKRAKEN AND THE ALIEN MINDBENDERS
Drive 1581 E Floppy Drive 3,5"
« Risposta #6 il: 28 Febbraio 2008, 17:59:16 »
 cavolo zimox che spettacolo!Complimenti

hiryu

  • Utente
  • **
  • Post: 649
    • http://hiryu.netsons.org/
  • Gioco Preferito: Wizard Of Wor
Drive 1581 E Floppy Drive 3,5"
« Risposta #7 il: 29 Febbraio 2008, 01:41:28 »
 @ zimox:

mi sembra una cosa interessante quella che hai fatto, ma, forse colpa dell'ora tarda, non ho ben capito cos'è di preciso e come l'hai realizzata... potresti fornire maggiori delucidazioni
Elwood: "E' partito un pistone"
Jake: "Poi torna?"
________________________________________________________
Hiryu @ http://hiryu.netsons.org | http://www.virb.com/hiryu

albman

  • Utente
  • **
  • Post: 125
  • Gioco Preferito: Wonder Boy / Bubble Bobble
Drive 1581 E Floppy Drive 3,5"
« Risposta #8 il: 02 Marzo 2008, 09:31:20 »
 mi associo assolutamente alla richiesta di hiryu, se hai voglia metti giu' una descrizione dettagliata che consenta anche a noi ti tentare la realizzazione... ho un 1541 malfunzionante e cassette piene di drive PC e amiga che fremono....  :sabber:
"If you want to become the old figure, use the power of your friendship, and fight me"

zimox

  • Utente
  • **
  • Post: 171
  • Gioco Preferito: trolls & tribulations
Drive 1581 E Floppy Drive 3,5"
« Risposta #9 il: 04 Marzo 2008, 21:39:11 »
 il 1541 non c'entra...
ho solo recuperato una logic board del --1581-- e' ho utilizzato un case del 1541 per metterci dentro tutto quello che serve per trasformarlo in un 1581 che ho chiamato 1582  :lol:

comunque...
ho solo seguito queste info recuperate per l' occasione dal mio HD.


 The 1581 was designed around the floppy drive used in the Amiga
   computers, but the 1581 can be outfitted with a standard high-density
   3.5" floppy drive with a minimum of effort. If you can't find an old
   Amiga to plunder, here's how to do it with an off-the-shelf PC floppy:
    1. As you connect the drive, match the red stripe on the ribbon cable
       to pin 1 of the drive's connector. Pin 1 may be marked by printed
       numbers on the circuit board, or a pin missing near one end of the
       connector, or a square solder pad on one of the end pins. If you
       can't see any markings, don't worry, plugging it in upside-down
       won't damage it. If it is marked but the connector won't go on,
       look at the key on the side of the connector. Some drives have the
       shell mounted upside-down, so you may have to remove the key with
       nippers or a file.
    2. Turn the 1581 on. The drive's light should be off. If the floppy
       drive's light is on, the connector is upside-down. Turn the 1581
       off.
    3. You will need to change a jumper on your drive. Write down the
       configuration before changing jumpers. All PC drives are
       factory-set for DS1. Change the jumper to select DS0. (If your
       drive's jumpers aren't identified, try them one at a time.) Turn
       the 1581 on. The floppy drive light should be on. Turn the 1581
       off.
    4. Now for the complicated part. PCs use pin 34 as the "disk-change"
       signal, but the 1581 uses pin 34 as a "ready" signal and uses pin
       2 for the "disk-change" signal. Check your drive for a jumper
       marked RY or RDY. If your drive has no such jumper, you will have
       to modify the cable (go to step 6).
    5. If your drive has a RY or RDY jumper and you don't want to modify
       the cable, you can remove the DC jumper and put it on RY/RDY. This
       will get the 1581 functional, but it will not detect a disk
       change, so you'll have to turn the drive off and on again when you
       change disks. If you are satisfied with this mode of operation, go
       to step 7. If not, put the jumper back on DC.
    6. Modify the ribbon cable as follows:
         1. with the floppy drive connected, write an F on the ribbon
            cable near the floppy drive connector. Disconnect and remove
            the cable. Note that wire 1 has the red stripe and wire 34
            does not.
         2. carefully cut wires 1 and 2 at the floppy drive connector,
            and pull the two wires back to the middle of the cable, one
            at a time, OR split the cable with a knife and cut wire 2
            only
         3. carefully cut wires 34 and 33 at the middle of the cable, and
            pull the two wires back toward the floppy drive connector,
            one at a time, so that they can easily join with wires 1 and
            2, OR if only wire 2 was cut, pull only wire 34 back
         4. connect wire 2 to wire 34 and insulate the connection
         5. connect wire 1 to wire 33 and insulate the connection (if
            applicable)
         6. pull wires 34 and 33 back toward the PC board connector
         7. connect wire 34 to wire 33 and insulate the connection
    7. If you don't care about looks, throw away the front cover and
       attach the LED board to the side of the case. Otherwise, you can
       drill and mill to suit before assembling the unit. If you want to
       use high-density disks in your 1581, you'll likely have to cover
       the high-density hole with an opaque label to fool the drive.


quasi tutti i drive che ho DD e HD (una ventina)sono andati bene a parte uno per amiga e i dei sony per pc.
il filo rosso del flat va messo al pin 1 e bisogna inserire correttamente gli spinotti dell' alimentazione in entrambe i terminali)
(ho cmq constatato che dei drive per amiga non sono come molti dicono-plug and play. per farli funzionare come 1581 necessitano di modifiche)


( c'e' anche un altro modo ma bisogna tagliare delle piste oltre che saldare dei cavetti sulla scheda e la cosa non mi piaceva.)
http://i29.tinypic.com/30av1gy.jpg

OT
se invece volete adattare dei floppy per usarli sull' amiga qualcosa ho trovato qui
http://tizeta2.altervista.org/amiga/tutori...a_floppy_drive/

spero di essere stato utile
No c64?, no party!

zimox

  • Utente
  • **
  • Post: 171
  • Gioco Preferito: trolls & tribulations
Drive 1581 E Floppy Drive 3,5"
« Risposta #10 il: 10 Marzo 2008, 22:08:37 »
 avevo da un po' di tempo questo  link e adesso lo uso(appiate pieta' e' la prima volta che uso frontpage)
posto il progettino step by step del 1581_b
il lettore floppy che ho usato e' uno normalissimo per pc a cui ho dissaldato la piazzola
DS1 per trasformarlo in DS0

http://www.commodore64.retrocomp.com/

saluti
 
No c64?, no party!

fostox

  • Utente
  • **
  • Post: 60
  • Gioco Preferito: The Staff of Karnath
Drive 1581 E Floppy Drive 3,5"
« Risposta #11 il: 19 Marzo 2008, 23:00:38 »
 a chi potesse interessare.....

http://www.jammingsignal.com/jppbm/1581kits.html